Prince Motor Spool Open Center Control Valve - 20 GPM, Model# RD-2575-T4-EDA1
Brand: Prince   
Valve will detent in both directions. Relief valve preset at 1500 PSI; adjustable to 3000 PSI. 3/4in. inlet and outlet, 1/2in. working ports. Motor locks in neutral. Includes motoring spool. 20 GPM flow rate. 3-year limited warranty. U.S.A.
*$99.99
Prince One Spool Control Valve, Model# HC-V-R22
Brand: Prince   
4-way with floats; has balanced spools with select fit. Load checks to prevent load drops when shifting directions. Good for use on snowplows, dozers, loaders etc. Float valves allow blade or bracket to float along ground. Will accept power beyond plug conversion. Preset at 2000 PSI. Adjustable from 1500 to 3000 PSI. USA
*$159.99
Prince PTO Tractor Pump 11.4 GPM, Model# HC-PTO-2A
Brand: Prince   
Gear-type, heavy-duty pump is designed for PTO drive operation on tractors of all sizes. No additional gearing is required. These pumps feature self-adjusting wear plates that seal off leakage and offset any wear or expansion that may occur during the life of the pump. High tensile aluminum housing, minimum gear clearance, cast iron endplates. Internal splined shafts go all the way through and are supported on both sides by roller bearings. All models have a #16 SAE inlet port and two #12 SAE outlet ports. Include #12 SAE to 3/4in. NPTF female adapter. Reservoir size should at least be as large as the output of the pump.
*$479.99
Prince PTO Tractor Pump 21 GPM, Model# HC-PTO-1A
Brand: Prince   
Gear-type, heavy-duty pump is designed for PTO drive operation on tractors of all sizes. No additional gearing is required. These pumps feature self-adjusting wear plates that seal off leakage and offset any wear or expansion that may occur during the life of the pump. High tensile aluminum housing, minimum gear clearance, cast iron endplates. Internal splined shafts go all the way through and are supported on both sides by roller bearings. All models have a #16 SAE inlet port and two #12 SAE outlet ports. Include #12 SAE to 3/4in. NPTF female adapter. Reservoir size should at least be as large as the output of the pump.
*$489.99
Prince PTO Tractor Pump 23 GPM, Model# HC-PTO-3A
Brand: Prince   
Gear-type, heavy-duty pump is designed for PTO drive operation on tractors of all sizes. No additional gearing is required. These pumps feature self-adjusting wear plates that seal off leakage and offset any wear or expansion that may occur during the life of the pump. High tensile aluminum housing, minimum gear clearance, cast iron endplates. Internal splined shafts go all the way through and are supported on both sides by roller bearings. All models have a #16 SAE inlet port and two #12 SAE outlet ports. Include #12 SAE to 3/4in. NPTF female adapter. Reservoir size should at least be as large as the output of the pump.
*$484.99
Prince PTO Tractor Pump 40 GPM, Model# HC-P-K11
Brand: Prince   
At 1000 PSI, direct drive pump delivers 40.1 GPM at 1000 RPM and over 20 GPM at 540 RPM. Pump has roller bearing construction, pressure balanced self-adjusting wear plates and an internally splined drive shaft, 1 3/8in.-21 tooth, so it needs no gear box. Handles pressures up to 2250 PSI. SAE O-ring ports: inlet #20 1 5/8in.-12, drain outlet #16 15/16in.-12, plus auxiliary outlet, #12 11/16in.-12. Includes #20 SAE to 2in. hose adapter and #16 SAE to 1in. female pipe. Easy installation using torque arm restraint. Reservoir size should at least be as large as the output of the pump. U.S.A.
*$499.99
Prince Standard 3-Way Control Valve, Model# RD-2575-T3-ESA1
Brand: Prince   
A control valve for operating single-acting cylinders. This valve has 3 ports, 3-position spring center to neutral and adjustable relief valve. Relief valve preset at 1500 PSI, adjusts up to 3000 PSI. Convertible from open to closed center. 3/4in. in/out ports, 1/2in. working ports. U.S.A.
*$109.99
Prince Standard 4-Way Control Valve, Model# RD2575T4ESA1
Brand: Prince   
Up to 20 GPM with 4 ports. Factory pre-set at 1500 PSI, has adjustable relief valve. For lower pressure, turn counter-clockwise. Adjustable from 1000 to 3000 PSI. Precision honed and plated, spools are hydraulically balanced. Spring centered. 3/4in. inlet/outlet ports, 1/2in. work ports. USA
*$99.99
Prince Standard Outlet End Plate, Model# SVE21
Brand: Prince   
Sectional body hydraulic directional control valves for mobile and industrial hydraulic systems. Power beyond plug capability. Use with double-acting cylinders. U.S.A.
*$39.99
Prince Tie-Rod Cylinder - 2500 PSI, 3in. Bore, 8in. Stroke, 1 1/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 2500 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 1/8
*$149.99
Prince Tie-Rod Cylinder - 2500 PSI, 4in. Bore, 8in. Stroke, 2in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 2500 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 2
*$229.99
Prince Tie-Rod Cylinder - 3000 PSI, 2 1/2in. Bore, 24in. Stroke, 1 1/4in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 1/4
*$179.99
Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 12in. Stroke, 1 1/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 1/8
*$139.99
Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 18in. Stroke, 1 1/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 18, Closed Pin Center (in.): 28 1/4, Shaft Diameter (in.): 1 1/8
*$149.99
Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 20in. Stroke, 1 1/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 20, Closed Pin Center (in.): 30 1/4, Shaft Diameter (in.): 1 1/8
*$159.99
Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 10in. Stroke, 1 3/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 10, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 3/8
*$179.99
Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 12in. Stroke, 1 3/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 3/8
*$189.99
Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 18in. Stroke, 1 3/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 18, Closed Pin Center (in.): 28 1/4, Shaft Diameter (in.): 1 3/8
*$199.99
Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 8in. Stroke, 1 3/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 3/8
*$169.99
Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 16in. Stroke, 1 3/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/2, Shaft Diameter (in.): 1 3/8
*$179.99
Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 18in. Stroke, 1 3/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 18, Closed Pin Center (in.): 28 1/4, Shaft Diameter (in.): 1 3/8
*$189.99
Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 24in. Stroke, 1 3/8in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 3/8
*$229.99
Prince Tie-Rod Cylinder - 3000 PSI, 4 1/2 in. Bore, 24in. Stroke, 2in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 36 1/4, Shaft Diameter (in.): 2
*$359.99
Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 10in. Stroke, 1 3/4in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 10, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 3/4
*$229.99
Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 12in. Stroke, 1 3/4in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 3/4
*$229.99
Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 16in. Stroke, 1 3/4in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/4, Shaft Diameter (in.): 1 3/4
*$249.99
Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 24in. Stroke, 1 3/4in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 3/4
*$289.99
Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 30in. Stroke, 1 3/4in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 30, Closed Pin Center (in.): 40 1/4, Shaft Diameter (in.): 1 3/4
*$299.99
Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 36in. Stroke, 1 3/4in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 36, Closed Pin Center (in.): 46 1/4, Shaft Diameter (in.): 1 3/4
*$319.99
Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 16in. Stroke, 2in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/2, Shaft Diameter (in.): 2
*$349.99
Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 18in. Stroke, 2in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 18, Closed Pin Center (in.): 30 1/4, Shaft Diameter (in.): 2
*$349.99
Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 24in. Stroke, 2in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 24, Closed Pin Center (in.): 36 1/4, Shaft Diameter (in.): 2
*$389.99
Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 30in. Stroke, 2in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 30, Closed Pin Center (in.): 42 1/4, Shaft Diameter (in.): 2
*$379.99
Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 8in. Stroke, 2in. Shaft
Brand: Prince   
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 2
*$269.99
Prince Two-Spool Control Valve, Model# RD522GCGA5A4B1
Brand: Prince   
Two spool to 25 GPM. With one standard 4-way port and one float. 3/4in. inlet and outlet ports; 1/2in. working ports. Valve will accept power beyond conversion plug. Internal load check. Relief pressure set at 2000 PSI; adjustable from 1500 PSI to 3000 PSI. Load check for each valve. U.S.A.
*$219.99
Prince Two-Way Detent Valve, Model# LS-3010-2
Brand: Prince   
For open center systems. Two-way detent; 3/4in. in/out 3/4in. work ports. Relief valve adjustable to 2750 PSI, preset at 2250 PSI, flow rating up to 25 GPM. Automatically kicks back to neutral when cylinder completes stroke. Built-in relief valve ports. Hydraulic balanced, hard chrome plated spool. Handle can be installed in up or down position. Detent release pressure adjustable from 600 to 2000 PSI. Warning: using a pressure detent in both directions can be dangerous. USA
*$84.99
Prince Welded Tee Cylinder - 2500 PSI, 2 1/2in. Bore, 12in. Stroke, 1 3/8in. Shank, Model# PMC-5412
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 12, Closed Pin Center (in.): 20, Shaft Diameter (in.): 1 3/8
*$159.99
Prince Welded Tee Cylinder - 2500 PSI, 2 1/2in. Bore, 16in. Stroke, 1 3/8in. Shaft, Model# PMC-5416
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 16, Closed Pin Center (in.): 24, Shaft Diameter (in.): 1 3/8
*$179.99
Prince Welded Tee Cylinder - 2500 PSI, 2 1/2in. Bore, 8in. Stroke, 1 3/8in. Shaft, Model# PMC-5408
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All-steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 8, Closed Pin Center (in.): 16, Shaft Diameter (in.): 1 3/8
*$149.99
Prince Welded Tee Cylinder - 2500 PSI, 3 1/2in. Bore, 24in. Stroke, 1 1/2in. Shaft, Model# PMC-5524
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 32, Shaft Diameter (in.): 1 1/2
*$229.97
Prince Welded Tee Cylinder - 2500 PSI, 3 1/2in. Bore, 36in. Stroke, 1 1/2in. Shaft, Model# PMC-5536
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 36, Closed Pin Center (in.): 44, Shaft Diameter (in.): 1 1/2
*$259.99
Prince Welded Tee Cylinder - 2500 PSI, 3in. Bore, 20in. Stroke, 1 1/2in. Shaft, Model# PMC-8320
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 20, Closed Pin Center (in.): 28, Shaft Diameter (in.): 1 1/2
*$219.99
Prince Welded Tee Cylinder - 2500 PSI, 3in. Bore, 36in. Stroke, 1 1/2in. Shaft, Model# PMC-8336
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 36, Closed Pin Center (in.): 44, Shaft Diameter (in.): 1 1/2
*$269.99
Prince Welded Tee Cylinder - 2500 PSI, 3in.Bore, 12in. Stroke, 1 1/2in. Shaft, Model# PMC-8312
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 12, Closed Pin Center (in.): 20, Shaft Diameter (in.): 1 1/2
*$174.99
Prince Welded Tee Cylinder - 2500 PSI, 3in.Bore, 16in. Stroke, 1 1/2in. Shaft, Model# PMC-8316
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 16, Closed Pin Center (in.): 24, Shaft Diameter (in.): 1 1/2
*$189.99
Prince Welded Tee Cylinder - 2500 PSI, 3in.Bore, 8in.Stroke, 1 1/2in. Shaft, Model# PMC-8308
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 8, Closed Pin Center (in.): 16, Shaft Diameter (in.): 1 1/2
*$159.99
Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 16in. Stroke, 2in. Shaft, Model# PMC-5616
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 16, Closed Pin Center (in.): 25, Shaft Diameter (in.): 2
*$249.99
Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 20in. Stroke, 2in. Shaft, Model# PMC-5620
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 20, Closed Pin Center (in.): 29, Shaft Diameter (in.): 2
*$269.99
Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 30in. Stroke, 2in. Shaft Size, Model# PMC-5630
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 30, Closed Pin Center (in.): 39, Shaft Diameter (in.): 2
*$309.99
Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 36in. Stroke, 2in. Shaft, Model# PMC-5636
Brand: Prince   
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 36, Closed Pin Center (in.): 45, Shaft Diameter (in.): 2
*$319.99
 
eBay Results
 TitlePriceShippingTotalCurrencyTime Left
Pneumatic Solenoid Valves, 24Vdc31.0010.3541.35USD
Pneumatic Air Hose Fitting 1" Barb Coupler 10 Pcs6.993.9410.93USD 40 minutes 44 seconds
Pneumatic Fittings, Push-Loc Type, Assortment15.0010.3525.35USD 43 minutes 38 seconds
Pneumatic Air Hose Fitting 1/2" Barb to 3/8" Female 2519.994.7224.71USD 44 minutes 8 seconds
1" SS Flanged Ball Valve by CF Fluid Controls (NEW!)29.990.0029.99USD 44 minutes 13 seconds
Numatics 081SS500K 3 Position Pneumatic Solenoid Valve49.990.0049.99USD 44 minutes 44 seconds
Ten 1/2" Dia Chrome Steel Bearing Hydraulic Check Balls5.003.008.00USD 50 minutes 19 seconds
Lot of (2) Watts Regulator 1" Bronze Ball Valves (NEW!)129.990.00129.99USD 52 minutes 25 seconds
FLEETGUARD / VOLVO 243004 P/N FF5018 16 PC LOT25.0015.0040.00USD 53 minutes 1 second
AEROQUIP PLUS 4 SPIRAL WIRE HYDRAULIC HOSE GH493-16 1"73.9955.00128.99USD 1 hour 5 minutes 48 seconds
SIEMENS POWERS 2651002 1/4 BARB E-P VALVE 120V 3W NEW49.990.0049.99USD 1 hour 16 minutes 9 seconds
Lot of 7 1-1/4" Hammond Threaded Bronze Ball Valves NEW209.990.00209.99USD 1 hour 18 minutes 11 seconds
Bench Top 3200PSI Thermal Cure-Hydraulic Electric PRESS999.990.00999.99USD 1 hour 22 minutes 6 seconds
AIR CYLINDER, 3/4" BORE X 1/2" STROKE, BIMBA NEW9.004.9513.95USD 1 hour 23 minutes 19 seconds
Rexroth hydraulic vane pump, 30 GPM @ 1800 RPM, PVV251.000.0051.00USD 1 hour 27 minutes 42 seconds
AIR CYLINDER, 9/16" BORE X 1 1/2" STROKE, BIMBA NEW13.004.9517.95USD 1 hour 35 minutes 9 seconds
ENERPAC JACK 1.5 TONS29.990.0029.99USD 1 hour 35 minutes 25 seconds
NEW 2PC SKID STEER 1” HYDRAULIC QUICK COUPLER PARKER149.990.00149.99USD 1 hour 39 minutes 26 seconds
AIR CYLINDER, 7/16" BORE X 1/2" STROKE, BIMBA, BLOCK9.004.9513.95USD 1 hour 41 minutes 3 seconds
hydraulic steering motor200.0015.00215.00USD 2 hours 41 seconds
LUBRICATOR, 3/8 NPT, WILKERSON #L16-03-000 , NEW19.0010.3529.35USD 2 hours 2 minutes 7 seconds
Custom Pnuematic Molding Press Table Top400.000.00400.00USD 2 hours 11 minutes 49 seconds
HUGE LOT OF PARKER PLUG VALVES 2M-PR4-VT-B PNEUMATIC 10.9914.9915.98USD 2 hours 25 minutes 35 seconds
LOT OF NEW AMERICAN AIR CYLINDERS PNEUMATIC 1250SS-11426.1714.9921.16USD 2 hours 26 minutes 55 seconds
LOT OF NEW AMERICAN AIR CYLINDERS 3 INCH PNEUMATIC NR14.5014.9929.49USD 2 hours 28 minutes 10 seconds
Deltrol Hydraulic Needle Valve 10000 PSI 1/4" S2500.999.9910.98USD 2 hours 32 minutes 59 seconds
Hydraulic hose fittings lot52.008.9560.95USD 2 hours 37 minutes 50 seconds
110 Hydraulic grease fitting assortment Zerk Lubricate19.997.9927.98USD 2 hours 52 minutes 6 seconds
Filtroil hydraulic oil filters20.0020.0040.00USD 2 hours 59 minutes 49 seconds
IMPERIAL EASTMAN ROL-AIR FLARING TOOL 637-F AVIATION2500.000.002500.00USD 3 hours 4 minutes 44 seconds
DEMO PARKER 10MF40SA10C Port. OIL HYDRAULIC FILTER CART399.990.00399.99USD 3 hours 22 minutes 21 seconds
Enerpac RC1006 RC10013 Repair Kit RC1006K 100 Ton Ram59.000.0059.00USD 3 hours 41 minutes 56 seconds
SMC CXSL10-35 Dual Rod Cylinder, 4 pieces8.005.7513.75USD 3 hours 46 minutes 28 seconds
Pneumactic cylinders rodless smc ncy2s32h pair49.0025.0074.00USD 3 hours 46 minutes 51 seconds
Hydraulic manifold 13" x 3" x 3" Yuken39.0020.0059.00USD 3 hours 46 minutes 51 seconds
Morin (Tyco) Rotary Pneumatic Actuator35.0014.5049.50USD 4 hours 5 minutes 48 seconds
Hydraulic valves Variable Shock-Less Yuken135.0025.00160.00USD 4 hours 6 minutes 7 seconds
Vacuum gauge diaphragm yamamoto keiki .1mpa55.0015.0070.00USD 4 hours 6 minutes 11 seconds
Hydraulic hose stainless metric New295.0095.00390.00USD 4 hours 6 minutes 11 seconds
Hydraulic pressure switch MJA-0150.0015.0065.00USD 4 hours 6 minutes 17 seconds
MAXIMATOR AIR DRIVEN LIQUID PUMP TYP;S60-02 NPT199.000.00199.00USD 4 hours 20 minutes 47 seconds
8 NEW COMPACT AIR 1" STAINLESS AIR CYLINDER Q87-135924.995.9030.89USD 4 hours 23 minutes 57 seconds
PARKER HYDRAULIC PUMP KIT COMMERCIAL SHEARING M37X49.9912.0061.99USD 4 hours 32 minutes 43 seconds
Hydraulic valves directional Yuken DSG-0395.0020.00115.00USD 4 hours 34 minutes 52 seconds
Grease Extreme Environment Aircraft Instrument Lithium?9.9910.5020.49USD 4 hours 37 minutes 11 seconds
OMNI ISI FLUID POWER INC. 4 WAY AIR VALVE 375-37-081-3739.008.9047.90USD 4 hours 40 minutes 35 seconds
Pneumatic Gate Valve Solenoid Whatman Flow Filter18.9911.9930.98USD 4 hours 42 minutes 38 seconds
HASKEL AAD-5 AIR AMPLIFIER299.000.00299.00USD 4 hours 55 minutes 1 second
Enerpac RSM 750 75 ton Flat-Jac rsm750450.000.00450.00USD 4 hours 55 minutes 10 seconds
17 pc AIR TOOL HOSE REPAIR FIX KIT SET FITTING CLAMP5.995.9211.91USD 5 hours 11 minutes 27 seconds
 
Previous Page   Next Page
Jump to page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Get eBay search results without all the crap at www.theDeCrapifier.com