 | Prince Welded Tee Cylinder - 2500 PSI, 3 1/2in. Bore, 24in. Stroke, 1 1/2in. Shaft, Model# PMC-5524
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 32, Shaft Diameter (in.): 1 1/2 | *$229.99 |
 | Prince PTO Tractor Pump 23 GPM, Model# HC-PTO-3A
Brand: Prince
Gear-type, heavy-duty pump is designed for PTO drive operation on tractors of all sizes. No additional gearing is required. These pumps feature self-adjusting wear plates that seal off leakage and offset any wear or expansion that may occur during the life of the pump. High tensile aluminum housing, minimum gear clearance, cast iron endplates. Internal splined shafts go all the way through and are supported on both sides by roller bearings. All models have a #16 SAE inlet port and two #12 SAE outlet ports. Include #12 SAE to 3/4in. NPTF female adapter. Reservoir size should at least be as large as the output of the pump. Max. PSI: 2,000, Shaft Diameter (in.): 1 3/8, Shaft Type: Spline 21-tooth, GPM: 23, Material: Aluminum and cast iron, Rotations Per Minute: 1,000, Weight (lbs.): 36 | *$484.99 |
 | Prince Motor Spool Open Center Control Valve - 20 GPM, Model# RD-2575-T4-EDA1
Brand: Prince
Valve will detent in both directions. Relief valve preset at 1500 PSI; adjustable to 3000 PSI. 3/4in. inlet and outlet, 1/2in. working ports. Motor locks in neutral. Includes motoring spool. 20 GPM flow rate. 3-year limited warranty. U.S.A. | *$99.99 |
| Prince Standard 3-Way Control Valve, Model# RD-2575-T3-ESA1
Brand: Prince
A control valve for operating single-acting cylinders. This valve has 3 ports, 3-position spring center to neutral and adjustable relief valve. Relief valve preset at 1500 PSI, adjusts up to 3000 PSI. Convertible from open to closed center. 3/4in. in/out ports, 1/2in. working ports. U.S.A. | *$109.99 |
 | Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 36in. Stroke, 2in. Shaft, Model# PMC-5636
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 36, Closed Pin Center (in.): 45, Shaft Diameter (in.): 2 | *$319.99 |
 | Prince 2-Spool Directional Control Valve, 3000 PSI, Model# RD522CCAA5A4B1
Brand: Prince
Ideal for front-end loaders. Features 3-position, 4-way spools with tandem center. 3000 PSI max. pressure. Nominal flow of 25 GPM. Adjustable relief (1500-3000 PSI). Spring center to neutral from work positions. Work ports are blocked in neutral. Use with open center circuits or closed center with optional closed center plug. | *$239.99 |
 | Prince Control Valve - 4-Way/3-Position Cylinder Spool, Model# SVW1BA1
Brand: Prince
Sectional body hydraulic directional control valves for mobile and industrial hydraulic systems. For use with double-acting cylinders. U.S.A. Max. Flow (GPM): 12, Inlet Port (in.): 7/8-14 ORB, Outlet Port (in.): 7/8-14 ORB, Working Port (in.): 3/4-16 ORB,, Max. PSI: 3,000, Directional Control: 4 way, 3 position, Adjustable Release Pressure PSI: 1,500 - 3,000 | *$79.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 30in. Stroke, 2in. Shaft Size, Model# PMC-5630
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 30, Closed Pin Center (in.): 39, Shaft Diameter (in.): 2 | *$309.99 |
 | Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 24in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 3/8 | *$229.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 24in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 24, Closed Pin Center (in.): 36 1/4, Shaft Diameter (in.): 2 | *$389.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 3in. Bore, 36in. Stroke, 1 1/2in. Shaft, Model# PMC-8336
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 36, Closed Pin Center (in.): 44, Shaft Diameter (in.): 1 1/2 | *$269.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 36in. Stroke, 2in.Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 36, Closed Pin Center (in.): 48 1/4, Shaft Diameter (in.): 2 | *$419.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 16in. Stroke, 2in. Shaft, Model# PMC-5616
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 16, Closed Pin Center (in.): 25, Shaft Diameter (in.): 2 | *$249.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 3in.Bore, 12in. Stroke, 1 1/2in. Shaft, Model# PMC-8312
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 12, Closed Pin Center (in.): 20, Shaft Diameter (in.): 1 1/2 | *$174.99 |
 | Prince Two-Spool Control Valve, Model# RD522GCGA5A4B1
Brand: Prince
Two spool to 25 GPM. With one standard 4-way port and one float. 3/4in. inlet and outlet ports; 1/2in. working ports. Valve will accept power beyond conversion plug. Internal load check. Relief pressure set at 2000 PSI; adjustable from 1500 PSI to 3000 PSI. Load check for each valve. U.S.A. | *$219.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 12in. Stroke, 1 1/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 1/8 | *$139.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 30in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 30, Closed Pin Center (in.): 40 1/4, Shaft Diameter (in.): 1 3/4 | *$299.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 18in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 18, Closed Pin Center (in.): 28 1/4, Shaft Diameter (in.): 1 3/8 | *$189.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 3 1/2in. Bore, 36in. Stroke, 1 1/2in. Shaft, Model# PMC-5536
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 36, Closed Pin Center (in.): 44, Shaft Diameter (in.): 1 1/2 | *$259.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 2 1/2in. Bore, 24in. Stroke, 1 1/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 1/4 | *$179.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 10in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 10, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 3/8 | *$179.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 2 1/2in. Bore, 12in. Stroke, 1 3/8in. Shank, Model# PMC-5412
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 12, Closed Pin Center (in.): 20, Shaft Diameter (in.): 1 3/8 | *$159.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 24in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 3/4 | *$289.99 |
 | Prince Bolt Kit for 5 Spools
Brand: Prince
Each kit contains: 3 bolts, 6 nuts and 6 washers. | *$9.99 |
| Prince Control Valve - 4-Way/3-Position Motor Spool, Model# SVW1CA1
Brand: Prince
Sectional body hydraulic directional control valves for mobile and industrial hydraulic systems. For use with hydraulic motors. Use with double-acting cylinders. U.S.A. Max. Flow (GPM): 12, Working Port (in.): 3/4-16 ORB, 8 SAE, Max. PSI: 3,000, Directional Control: 4 way, 3 position, Adjustable Release Pressure PSI: 1,500 - 3,000 | *$89.99 |
 | Adjustable Flow Control Valve - 3/4in. Port Size
Brand: Prince
Controls the speed of hydraulic motors. Rated up to 3000 PSI. Rated flow 0-30 GPM. This type of valve will start and stop a hydraulic motor or cylinder and vary the speed over a wide range. Once the speed is set it will remain constant regardless of load variation. Any remaining flow is bypassed to the excess flow port to return to tank or to power another hydraulic function. U.S.A. | *$84.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 30in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 30, Closed Pin Center (in.): 42 1/4, Shaft Diameter (in.): 2 | *$379.99 |
| Prince Tie-Rod Cylinder - 2500 PSI, 4in. Bore, 8in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 2500 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 2 | *$229.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 3in.Bore, 16in. Stroke, 1 1/2in. Shaft, Model# PMC-8316
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 16, Closed Pin Center (in.): 24, Shaft Diameter (in.): 1 1/2 | *$189.99 |
 | Prince Detent Valve, 3/4in. Port Size, Model# LS-3000-2
Brand: Prince
Factory pre-set at 1500 PSI; adjustable from 1000 to 3000 PSI. Spring centered. 3/4in. inlet/outlet and 3/4in. work ports. For use with 5in. and larger cylinders and 20 gallon pumps. Up to 25 gallons per minute. USA | *$99.99 |
 | Prince Heavy Duty Hydraulic Motor - 14 GPM, 1800 PSI, Model# ADM200-4RP
Brand: Prince
For light and medium duty applications. Replacement for Charlynn H, White HS, and Ross TRW MG series. Maximum inlet pressure is 2500 PSI and maximum back pressure is 1000 PSI. Fully reversible, 4-bolt mount with 1in. x 1 3/4in. shaft with 1/4in. keyway. 1/2in. NPTF ports. Orbiting Gerotor Principle. Mounting Type: 4 bolt, Shaft Dimensions Diameter x L (in.): 1 x 1 3/4, Port Size (in.): 1/2 NPTF, Displacement (cu. in.): 12.15, Max. RPM: 400, Max. PSI: 1,800, Max. Torque (in.-lbs.): 2,305, Max. Flow (GPM): 14 | *$279.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 24in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 3/8 | *$229.99 |
 | Prince Welded Tee Cylinder - 2500 PSI, 2 1/2in. Bore, 8in. Stroke, 1 3/8in. Shaft, Model# PMC-5408
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All-steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 8, Closed Pin Center (in.): 16, Shaft Diameter (in.): 1 3/8 | *$149.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 16in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/2, Shaft Diameter (in.): 1 3/8 | *$179.99 |
 | Prince Hydraulic Control Valve - 8 GPM, 3-Spool, Model# MB31BBB5C1
Brand: Prince
This Prince hydraulic control valve features a compact design that is ideal for tractors and other low flow operations. SAE #8 ports eliminate leakage, enclosed handles eliminate exposure to elements. 4-way, 3-position spring center; can be converted to closed center or Power Beyond. 3500 max. PSI; 2000-3500 PSI adjustable relief, preset at 2500 PSI. Max. Flow (GPM): 8, Inlet Port (in.): SAE ;pound;8, Outlet Port (in.): SAE ;pound;8, Working Port (in.): SAE ;pound;8, Max. PSI: 3,500, Directional Control: 4-way, 3-position, Spool (qty.): 3, Adjustable Release Pressure PSI: 2,000-3,500, preset 2,500 | *$269.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 16in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/4, Shaft Diameter (in.): 1 3/4 | *$249.99 |
 | Prince SP20 Series Hydraulic Gear Pump - .976 Cu. In., CCW, Model# SP20B16A9H4-L
Brand: Prince
Compact, lightweight gear pump is built with high-strength aluminum body housing and end covers. Delivers high efficiency and low noise. One-pc. hardened alloy steel gears and driveshaft. Operating pressures up to 3000 PSI. Ideal for material handling, aerial lifts, lawn and turf care, agriculture, construction and other applications. 3-year limited warranty. U.S.A. | *$209.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 12in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 3/4 | *$229.99 |
 | Prince Heavy Duty Hydraulic Motor - 12 GPM, 2200 PSI, Model# ADM50-4RP
Brand: Prince
For light and medium duty applications. Replacement for Charlynn H, White HS, and Ross TRW MG series. Maximum inlet pressure is 2500 PSI and maximum back pressure is 1000 PSI. Fully reversible, 4-bolt mount with 1in. x 1 3/4in. shaft with 1/4in. keyway. 1/2in. NPTF ports. Orbiting Gerotor Principle. | *$249.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4 1/2 in. Bore, 24in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 36 1/4, Shaft Diameter (in.): 2 | *$359.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 18in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 18, Closed Pin Center (in.): 30 1/4, Shaft Diameter (in.): 2 | *$349.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 48in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 48, Closed Pin Center (in.): 60 1/4, Shaft Diameter (in.): 2 | *$549.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 8in. Stroke, 1 1/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 1/8 | *$129.99 |
 | Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 20in. Stroke, 1 1/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 20, Closed Pin Center (in.): 30 1/4, Shaft Diameter (in.): 1 1/8 | *$159.99 |
| Prince Heavy Duty Hydraulic Motor - 14 GPM, 2000 PSI, Model# ADM100-4RP
Brand: Prince
For light and medium duty applications. Replacement for Charlynn H, White HS, and Ross TRW MG series. Maximum inlet pressure is 2500 PSI and maximum back pressure is 1000 PSI. Fully reversible, 4-bolt mount with 1in. x 1 3/4in. shaft with 1/4in. keyway. 1/2in. NPTF ports. Orbiting Gerotor Principle. | *$259.99 |
 | Prince Directional Control Valves-Inlet Section, Model# 2012H
Brand: Prince
Sectional body hydraulic directional control valves for mobile and industrial hydraulic systems. You can combine 1 to 10 sections per valve bank. Standard features: Load checks on each work port. Hard chrome plated spools, Compact construction to save space. Reversible handle. Extra fine spool metering. Parallel or tandem circuit. Foot mounting. Maximums: 20 GPM; operating temperature 180deg F and 3500 PSI. Power beyond plug and pressure, interchangeable with Gresen V20. | *$89.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 8in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 3/8 | *$169.99 |
| Prince Energy Motor Spool Open Center Control Valve - 20 GPM, Model# RD-2575-M4-EDA1
Brand: Prince
Comes with motoring spool that will free wheel in neutral. Valve will detent in both directions. Relief valve preset at 1500 PSI; adjustable to 3000 PSI. 3/4in. inlet and outlet, 1/2in. working ports. Includes motoring spool. 20 GPM flow rate. 3-year limited warranty. U.S.A. | *$109.99 |
 | Priority Flow Divider - 30 GPM Capacity
Brand: Prince
Divider has adjustable orifice. Rated up to 3000 PSI. Priority flow divider separates one input flow into two output flows. 0-30 GPM capacity. Priority flow is adjustable. One flow is constant and unaffected by input flow variations or load changes. The other port is an excess flow that can provide another circuit. 3/4in. ports. | *$94.99 |
| Prince Directional Control Valves-Outlet Section
Brand: Prince
Sectional body hydraulic directional control valves for mobile and industrial hydraulic systems. You can combine 1 to 10 sections per valve bank. Standard features: Load checks on each work port. Hard chrome plated spools, Compact construction to save space. Reversible handle. Extra fine spool metering. Parallel or tandem circuit. Foot mounting. Maximums: 20 GPM; operating temperature 180deg F and 3500 PSI. Power beyond plug and pressure, interchangeable with Gresen V20. | *$59.99 |
|
